Welmac  UK  Ltd
Welbourn
Lincoln,  LN5 0QL
Tel:  01400 272475      Mob:  0796 108 9170
Email:  welmacuk@btconnect.com

 
 
 

[  horizontal  grinder  ]
 

 
DURATECH.... Clearing the way for a better tomorrow.
 
The Model 9564 Horizontal Grinder is the newest member of the DuraTech line up of industrial grinders.
It comes with the CAT C27 Tier II diesel engine that puts out 950 hp (708.4 kw).
The HPTO wet clutch transfers power to the 64 inch wide, 12,1000 lb (5488.5 kg) hammermill. The hammermill is fed by a self-governing
floor apron and feed roller through a 60" (152.4 cm) wide x 40" (101.6 cm) high feed opening.
The high capacity 315 cu ft (11.66 cu yd) (8.91 cu mtr) hopper will handle the largest trees and stumps.
 
Features Include:
  • Caterpillar C27 950 hp (708.4 kw) Tier II diesel engine.
  • PT-Tech HPTO 15 microprocessor controlled wet clutch.
  • Enclosed engine compartment with convenient access doors.
  • Self-cleaning air intake system.
  • 30ft x 48" wide oscillating stacking conveyor.
  • 10 groove belt drive connects the wet clutch to the hammermill.
  • 12,100 lb (5488.47 kg) 64" wide hammermill.
  • 24 hammers with a tip swing of 51" (129.54 cm).
  • 60" (152.4 cm) wide x 40" (101.6 cm) high feed opening.
  • Self-governing floor apron and feed roller - 42" (106.68 cm) diameter.
  • Large 315 cu ft (8.91 cu mtr) hopper; 61½" (156.2 cm) wide x 248" (629.9cm) long.
  • Four hydraulic stabiliser legs.
  • 91,500 pounds (41,503.7 kg) of engineering construction.
                         
             
                         
  Self Cleaning
Air Intake System		 Self Governing Apron
and Feed Roller Feed
Large Hammermill		 Oscillating Stacking
Conveyor Pivots
40 Degrees		   10 Groove Belt
Drive System		   12,100 lb
(5,488.47 kg)
Hammermill		   HPTO
Wet Clutch		  
                         
 
 

SPECIFICATIONS
Weight 91,500 lbs (41,503.7 kg)   Electric Governing System Programmable Logic Controller *
Transport Length 53' (16.15 m)   Hydraulic Drive Controls Two Load Sensing Pumps
Transport Width 11' 10" (3.61 m)   Hammermill Rotor Shaft 5 7/16" (13.81 cm)
Transport Height 13' 5" (4.09 m)   Rotor Width 64" (162.6 cm)
Axle Spacing 57½" (1.46 m)   Rotor Speed 1125 rpm
5th Wheel Weight 33,750 lbs (15,308.74 kg)   Tip Swing Diameter 50¾" (126.9 cm)
Total Axle Weight 57,750 lbs (26, 195 kg)   Number of Tips 24
Engine Caterpillar C27 Tier II 950 hp (708.4 kw)   Cylinder Mid Plates 1½" (3.81 cm) Thick x 39" (99.06 cm)
Clutch HPTO 15 TD Wet Clutch     Diameter
Fuel Tank 380 Gallons (1440 ltr)   Cylinder End Plates 1½" (3.81 cm) Thick x 40" (101.6 cm)
Fuel Consumption 47.5 gal/hr (179.8 ltr/hr)     Diameter T-1 Material
Hydraulic Tank 145 Gallons (548.9 ltr)   Hammermill Weight 12,100 lbs (5488.47 kg) **
Rotor Drive 10 Groove 8V   Hammer Rod Size 3¼" (8.26 cm)
Hopper Capacity 315 Cu ft (8.91 cu mtr)   Feeder Rotor Diameter 42" (106.9 cm)
Hopper Width 61½" (156.2 cm) Bottom   Feeder Rotor Drive Dual Orbit Motor/Dbl Reduction Gears
  74" (187.7 cm) Top   Screen Area 4340 sq in (11023.6 sq cm)
Hopper Length 248" (629.9 cm) Door Up   Screen Thickness 1" (2.54 cm)
  300" (762 cm) Door Down   Belly Conveyor 28½" (8.69 cm) L x 54" (137.2 cm) W
Hopper Depth 35" (88.9 cm)   Stacking Conveyor 366" (9.3 m) L x 48" (121.9 cm) W
Feed Opening 61½" x 40" (106.6 cm x 156.2 cm)   Oscillation 40 Degrees, Side to Side
Feed Height 96" (234.8 cm)   Stacking Height 22' (6.71 m) @ 30 Degree Incline

* The PLC (Programmable Logic Controller) regulates feed rate based on rotor speed. Feed rate is proportional to rotor speed.
Maximum feed rate is adjustable.   ** Hammermill weight consists of shaft, hammer rods, bits, hardware and tool holders.
 

Illustrations, specifications and descriptions contained herein were accurate at the time of publication, but are subject to change
without notice.
Illustrations may include optional equipment and accessories and may not include all standard equipment.
 

Return to Welmac Duratech Models                    Visit Duratech Industries Home Page
 

 

Duratech  -  Tub Grinder Hire  -  Stump Grinders  -  Woodchippers  -  D5600 Shredder  -  Used Equipment  -  News/Shows  -  Home
 
© Welmac UK Ltd, 2006 - 2008